Articulating boom lifts in the 80 to 85 foot class are designed for up-and-over access around obstacles on large, complex sites. Their multi-joint booms allow frequent, precise adjustments at height, making them a good fit for outdoor work that demands careful positioning, including maintenance at facilities like power stations or industrial plants. In this range, platform heights are about 80–85 feet with working heights typically in the high-80s to low-90s. Horizontal outreach generally lands in the mid-50s to around 60 feet, and platform capacity is commonly near 500 pounds for two workers and tools. These internal-combustion units are set up for rough terrain with four-wheel drive and steer to help position safely on uneven ground.

The 135’ IC articulating boom lift is built for challenging jobsites and extreme height work. It runs on an internal-combustion powertrain for outdoor use and uses an articulating boom for precise, up-and-over positioning around obstacles. Four-wheel drive and steer support maneuverability on rough terrain, and continuous rotation helps you line up the platform quickly. In this class, platform heights are around 135 feet with working heights typically in the high-130s to low-140s. Horizontal outreach commonly falls in the high-60-foot range, and platform capacities often land between 500 and 600 pounds for two workers and tools. Models include: Genie Z-135/70. Rent a 135-ft IC articulating boom lift from an EquipmentShare location near you.

Articulating boom lifts in the 40 to 45 foot class are designed for up-and-over access around obstacles in tight layouts. Their multi-joint booms let operators make continual, precise adjustments, which is useful for utility repair, facility maintenance, and construction work in awkward or congested areas. Internal-combustion power with rough-terrain drive helps on uneven outdoor sites.

Articulating boom lifts in the 30 to 35 foot class are built for up-and-over access in tight layouts where obstacles block a straight approach. Their multi-joint design allows frequent repositioning and precise placement, making them a good fit for utility maintenance, light construction, and repair work in constrained outdoor areas. In this range, platform heights are about 30–35 feet with working heights roughly 36–41 feet. Horizontal outreach commonly falls around 19–22 feet, and platform capacity is typically near 500 pounds.

Articulating boom lifts in the 60 to 65 foot class are built for up-and-over access in large, complex layouts. Their multi-joint booms let operators make continual, precise adjustments around obstacles, which is useful in settings like aircraft hangars, plants, and congested outdoor sites. In this range, platform heights are about 60–65 feet with working heights typically in the high-60s to low-70s. Horizontal outreach commonly falls in the mid-30s to low-40s feet, and platform capacity is often around 500 pounds. These internal-combustion units are set up for rough terrain with four-wheel drive and steer to position confidently on uneven ground.

Articulating boom lifts in the 125-foot class are built for outdoor work that needs up-and-over reach around obstacles. Platform heights are around 125 feet with working heights typically in the low 130s, and horizontal outreach commonly falls in the 60-foot range. Platform capacities are often between 500 and 1,000 pounds to handle two workers and tools. These internal-combustion units run on diesel and are set up for rough terrain with four-wheel drive and steer for positioning on uneven ground. Continuous turntable rotation and platform rotation are commonly included to fine-tune your approach at height. Models include: JLG 1250AJP.

Available when and where needed.

Hybrid articulating boom lifts in the 60 to 65 foot class combine battery power with an onboard engine for flexible, low-emission operation. They're built for up-and-over work around obstacles on mixed indoor/outdoor jobs, with rough-terrain drive for positioning outside and quiet electric mode for work in enclosed areas. Platform heights are typically around 60–65 feet, with working heights in the high-60s, horizontal outreach in the mid-30s, and platform capacities commonly between 500 and 600 pounds.

Atrium (spider) lifts in the 70 to 80 foot class are built for access in tight, hard-to-reach areas. Stowed widths typically fit through standard double doors, and the tracked undercarriage provides low ground pressure for travel across finished floors. Outriggers level the machine for safe setup on uneven surfaces in lobbies, atriums, and other confined spaces. In this range, platform heights are about 70–80 feet with working heights generally in the high-70s to mid-80s, and horizontal outreach commonly in the low-30s to around 40 feet. Platform capacities often fall between 400 and 500 pounds. Many units run electric or bi-energy power for indoor use with the option to operate outdoors when needed.

Atrium (spider) lifts in the 60 to 65 foot class are built for access in tight, hard-to-reach areas. Stowed widths typically fit through standard double doors, and the tracked undercarriage provides low ground pressure and non-marking travel on finished floors. Outriggers level the machine on uneven surfaces for safe setup in lobbies, atriums, and other confined spaces. In this range, platform heights are about 60–65 feet with working heights generally in the high-60s, and horizontal outreach commonly around the mid-20s to low-30s feet. Many units run on electric or bi-energy power for indoor work with the option to operate outdoors when needed.

Electric articulating boom lifts in the 30 to 34 foot class are built for precise, up-and-over access indoors. Their multi-joint booms make frequent repositioning easy around ducts, conveyors, or mezzanines, and the electric powertrain supports zero-emission, low-noise work in occupied spaces. In this range, platform heights are about 30–34 feet with working heights roughly in the mid- to high-30s, horizontal outreach commonly in the high-teens to low-20s feet, and platform capacities often around 500 pounds. Compact dimensions and non-marking tires help in aisles and finished areas. EquipmentShare offers models like the JLG E300AJP.

Electric articulating boom lifts in the 45 foot class are built for precise, up-and-over access on indoor jobs and smooth outdoor surfaces. Their multi-joint booms reach over obstacles such as racking, ductwork and equipment. The battery-powered drive allows zero-emission, low-noise operation in occupied buildings. In this range, platform heights are about 45 feet, with working heights around 51 feet. Horizontal outreach is commonly in the low to mid-20s, and platform capacity is typically 500 pounds. The wide chassis adds stability at height, and non-marking tires protect finished floors.

Narrow electric articulating boom lifts in the 40 foot class are built for indoor work where space is tight. A stowed width under 5 feet lets them fit through standard doorways, down aisles and into congested work areas. They still offer up-and-over reach around obstacles. Electric power keeps operation quiet and emission-free in occupied spaces. In this range, platform heights are about 40 feet, with working heights around 46 feet. Horizontal outreach is commonly in the low 20s, and platform capacity is typically 500 pounds. Non-marking tires and a compact turning radius make them well suited to warehouses, manufacturing facilities and commercial interiors.

Electric telescopic boom lifts in the 60 to 66 foot class deliver straight-line reach and height with zero-emission, low-noise operation. They are a strong fit for large indoor spaces such as distribution centers, arenas and atriums. They also suit outdoor work in noise- or emission-sensitive areas, including hospitals, schools and urban sites. In this range, platform heights are about 60 to 66 feet, with working heights typically in the high 60s to low 70s. Horizontal outreach commonly falls between the high 30s and mid-40s, and platform capacity is often around 500 pounds. Battery-electric drive lowers fuel and maintenance costs while still providing reliable performance across a full shift.

Electric scissor lifts in the 45 to 46 foot platform height class are built for high indoor or slab-outdoor work where vertical reach and a compact footprint are both important. They provide stable, straight-up access for maintenance, installation, and construction tasks in warehouses and large commercial interiors. Working heights can land in the low-50s, platform capacities commonly range from 700 to 1,000 lb, and overall widths are often around 55 inches to navigate tighter aisles. Electric drive and non-marking tires support zero-emission, low-noise operation on finished floors. Typical models include the 4555SE and the GS-4655.

The 26' micro electric scissor lift with a step-up platform is ideal for reaching tight ceiling heights and confined indoor spaces where a standard scissor lift's footprint won't fit. The compact, low-profile design and non-marking tires make it ideal for warehouses, retail buildouts, and finished-floor jobsites, while the step-up platform adds extra working height without sacrificing maneuverability.

For indoor work where a ladder feels too limiting and a full-size lift is too much, the Electric Scissor Lift, 10' Micro with Step-up Platform hits the sweet spot. Its compact frame maneuvers easily through doorways, hallways, and tight spaces, while electric power keeps operation quiet and emissions-free. The step-up platform provides a low entry height, making it quick and easy for operators to get on and off throughout the day. It's ideal for electrical work, HVAC installs, drywall, painting, and maintenance tasks in finished interiors.

Micro electric scissor lifts in the 26-foot platform height class are built for indoor work where a standard 26-footer is too large. The narrow chassis fits tight aisles and doorways, and electric drive supports low-noise, zero-emission operation on finished floors. Working heights typically reach the low-30s, platform capacities commonly fall around 500–600 lb, and overall widths are generally about 30–32 inches for access through standard doors. These lifts are a good fit for maintenance, installation, and light construction in congested interiors where precise positioning matters. Typical models include the MEC Micro 26.

Electric scissor lifts in the 10 to 12 foot platform height range are built for indoor work where compact size, quiet operation, and zero emissions matter. They're a good fit for maintenance, installation, and light construction tasks in tight corridors, retail spaces, and facilities with finished floors. Typical working heights are roughly 10 to 12 feet, with platform capacities that commonly fall around 500 pounds. Narrow widths fit standard doorways and aisles, and non-marking tires help protect sensitive surfaces. Typical models include the SS1230E in this class.

Electric scissor lifts in the 32-foot platform height class with a wide chassis are built for indoor work in large aisles and open interiors like warehouses, hangars, and theaters. Working heights typically reach 30 to 40 feet, platform capacities commonly range from 700 to 1,000 pounds, and overall widths are generally about 46 inches for added deck space. Zero-emission operation, non-marking tires, and smooth proportional controls support maintenance, installation, and repair work on level surfaces. Typical models include the 3346SE, ES3246, and GS-3246.

Electric scissor lifts in the 26-foot platform height class with a wide chassis are built for indoor work in larger aisles and open interiors like warehouses, hangars, and theaters. The wider platform provides more workspace and stability for mid-height tasks on finished floors with zero-emission, low-noise operation. Working heights typically reach the low-30s, platform capacities commonly range from 700 to 1,000 pounds, and overall widths are generally around 46 inches for added deck space. Non-marking tires and smooth proportional controls support precise positioning on level surfaces for maintenance, installs, and repairs. Typical models include the Genie GS-2646 in this class.

Electric scissor lifts in the 26-foot platform height class with a narrow chassis are built for indoor work where aisle space and doorway clearance are tight. Zero-emission operation and non-marking tires make them a good fit for warehouses, commercial interiors, and other finished spaces. Working heights typically reach the low-30s, platform capacities commonly fall around 500–700 lb, and overall widths are generally about 30–32 inches to pass through standard doors. Smooth proportional controls support precise positioning for mid-height tasks like sign hanging, lighting, and repairs on level surfaces. Typical models include the 2632SE, ES2632, and GS-2632.

Micro electric scissor lifts in the 19-foot platform height class are built for tight, indoor spaces where compact size and low noise matter. The step-up platform gives operators extra reach without moving the machine, which helps when working over ductwork, shelving, or fixtures. Electric drive supports zero-emission operation in occupied areas. Typical working heights land in the mid-20s, with platform capacities commonly in the 400–500 lb range. Narrow chassis widths fit standard doorways and aisles, non-marking tires protect finished floors, and tight turning helps in congested layouts. The step-up feature generally adds several inches to about a foot of effective reach for precise positioning at task height. Typical models include the MEC Micro 19-XD.

Micro electric scissor lifts in the 19-foot platform height class are built for tight indoor spaces where a standard 19-footer is too wide. They offer zero-emission, low-noise operation and a narrow chassis that fits through standard doorways and aisles, making them a good choice for maintenance, installs, and light construction on smooth floors. Working heights commonly reach the mid-20s, with platform capacities typically around 500 pounds for one or two operators with tools. Compact dimensions, non-marking tires, and tight turning help in congested areas and finished interiors. Typical models include the MEC Micro 19 in this class.

Electric scissor lifts in the 32-foot platform height class with a narrow chassis are built for indoor access in tight aisles and doorways. Zero-emission operation and non-marking tires make them a good fit for warehouses, commercial interiors, and other finished spaces where noise and floor protection matter. Working heights typically reach the high-30s, platform capacities commonly fall around 500–700 lb, and overall widths are generally about 30–32 inches to pass through standard doors. Smooth proportional controls support precise positioning for mid-height tasks like sign hanging, lighting, and repairs on level surfaces. Typical models include the Genie GS-3232 in this class.

Electric scissor lifts in the 20-foot platform height class with a narrow chassis are built for indoor access in tight aisles and doorways. Zero-emission operation and non-marking tires make them a good fit for warehouses, commercial interiors, and other finished spaces where noise and floor protection matter. Working heights typically reach the mid-20s, platform capacities commonly fall between 600 and 800 lb, and widths are generally around 30–32 inches to pass through standard doors. Smooth proportional controls support precise positioning for maintenance, installation, and light construction on level surfaces.

Electric scissor lifts in the 40-foot platform height class with a narrow chassis are built for high indoor reaches in tighter aisles and mezzanine areas. Working heights typically land in the mid-40s, platform capacities commonly fall around 600–800 lb, and overall widths are generally about 46–48 inches for added deck space without going to a wide-body unit. Electric drive and non-marking tires support low-noise, zero-emission operation on finished floors. These lifts are a good fit for maintenance, lighting, inventory work, and installs on smooth, level surfaces where vertical reach and compact footprint both matter. Typical models include the 4046SE, GS-4046 E Drive, and GS-4047.

Electric scissor lifts in the 19-foot platform height class with a narrow chassis are built for indoor work in tight aisles and doorways. Working heights can reach the mid-20s, platform capacities commonly fall around 500–600 lb, and widths are generally about 30–32 inches to fit through standard doors. Electric drive and non-marking tires support low-noise, zero-emission operation on finished floors for maintenance, installs, and light construction. Typical models include the 1930SE, ES1932, and GS-1930.

Electric scissor lifts in the 40-foot platform height class with a wide chassis are built for high indoor or slab-outdoor work where extra deck space and stability are important. They're a good fit for maintenance, installs, inventory, and construction tasks in warehouses, hangars, and large commercial interiors. Platform heights are around 40 feet, with working heights generally in the mid- to high-40s. Platform capacities commonly range from 700 to 1,200 lb, and overall widths are typically about 46 to 69 inches depending on configuration. Electric drive supports low-noise, zero-emission operation, with non-marking tires for finished floors.

Pusharound vertical mast lifts in the 7-foot platform height class are built for low-rise indoor work where tight access and quick setup matter. They're a good fit for maintenance, electrical, retail resets, and light installation in aisles, offices, and finished interiors. Platform heights are around 7 feet with working heights typically in the low teens. Platform capacities commonly fall between 300 and 375 pounds, and overall widths are usually under 30 inches to pass through standard doors. Non-marking casters and lightweight construction help protect floors, and simple controls support fast, precise positioning on level surfaces. Typical models include the JLG Ecolift 70.

Hybrid rough-terrain scissor lifts in the 50 to 55 foot class are built for outdoor construction and maintenance where long runtimes and a large platform are required. Hybrid power combines battery operation with an onboard engine for lower emissions and extended duty cycles, while 4WD and rough-terrain drive help position confidently on uneven ground. In this range, platform heights are typically in the high-40s to low-50s with working heights in the low- to mid-50s. Wide decks are commonly 7–8 feet across with extensions that reach about 12–16 feet in length, and platform capacities often fall between 1,000 and 1,500 pounds. Typical models include the Haulotte HS5390.

Rough-terrain scissor lifts in the 36 to 45 foot class with wide decks are built for outdoor access where extra platform space and load capacity matter. They're a solid choice for framing, siding, steel work, and MEP rough-in when crews need room for tools and materials at height. Diesel or dual-fuel power, 4WD, high ground clearance, and rough-terrain tires support positioning on slopes and soft ground. Platform heights are 36–45 feet with working heights in the low-40s to low-50s. Wide platforms are typically 7–8 feet across with roll-out extensions that reach about 12–16 feet in length, and platform capacities commonly fall between 1,500 and 2,500 pounds. Typical models include the 430LRT, GS-4390 RT, and RT4394.

Rough-terrain scissor lifts in the 26 to 29 foot class are built for outdoor work on unfinished surfaces where extra traction and stability are required. They're a good fit for framing, cladding, utilities, and site maintenance when you need straight-up access and room on the deck for tools and materials. In this range, platform heights are 26–29 feet with working heights typically in the low-30s. Platform capacities commonly fall around 1,000–1,250 pounds, and wide decks with extensions add reach across work areas. Diesel or dual-fuel power, 4WD, high ground clearance, and aggressive RT tires help with positioning on uneven ground. Typical models include the JLG RT2669 and the Skyjack SJ6826 RT.

Rough-terrain scissor lifts in the 30 to 35 foot class are built for outdoor access on unfinished surfaces where traction and deck space matter. They're a good fit for framing, siding, utilities, and general site work when you need straight-up reach and room for tools and materials. Platform heights are 30–35 feet with working heights typically in the high-30s to low-40s. Platform capacities commonly fall around 1,000–1,250 lb, with wide decks and extensions to span work areas. Diesel or dual-fuel power, 4WD, high ground clearance, and RT tires help with positioning on uneven ground. Typical models include the JLG RT3369 and the Skyjack SJ6832 RT.

Rough-terrain scissor lifts in the 50 to 55 foot class with wide decks are built for outdoor work where crews need room at height and steady performance on unfinished surfaces. They're a good fit for structural work, siding, and MEP rough-in on large commercial sites. Platform heights are 50–55 feet with working heights typically in the high-50s to low-60s. Wide platforms are commonly 7–8 feet across with roll-out extensions that reach about 12–16 feet in length, and platform capacities often fall between 1,500 and 2,000 pounds. Diesel or dual-fuel power, 4WD, high ground clearance, and rough-terrain tires help with positioning on slopes and soft ground, with stabilization features available for setup on uneven areas. Typical models include the Genie GS-5390 RT.

Rough-terrain scissor lifts in the 60 to 65 foot class with wide decks are built for high outdoor work where crews need space, stability, and long duty cycles. They're a strong fit for structural steel, façade work, and MEP rough-in on large commercial sites with unfinished or uneven surfaces. Platform heights are 60–65 feet with working heights typically in the high-60s to low-70s. Wide platforms are commonly 7–8 feet across with roll-out extensions that reach about 12–16 feet in length, and platform capacities often fall between 1,200 and 1,500 lb. Diesel or hybrid power, 4WD, high ground clearance, and rough-terrain tires support travel on slopes and soft ground, with stabilization features available for setup on irregular areas.

Hybrid rough-terrain scissor lifts in the 36 to 45 foot class are built for outdoor work where you need a large platform and long duty cycles. Hybrid power combines battery operation with an onboard engine to extend runtime and reduce emissions and noise on the job. Wide decks give crews room for tools and materials, and rough-terrain drive helps position confidently on uneven surfaces. Platform heights in this range are typically 36–45 feet, with working heights roughly in the low-40s to low-50s. Decks are commonly 7–8 feet wide with extensions that can reach 12–16 feet in length, and platform capacities often fall between 1,000 and 1,500 pounds. Machines in this class usually include 4WD, oscillating axles or stabilization, high ground clearance, and aggressive RT tires for performance on slopes and soft ground. Typical models include the Haulotte HS4390 E PRO in this category.

Rough-terrain scissor lifts in the 36 to 45 foot class are built for outdoor access on unfinished surfaces where traction, stability, and deck space matter. They provide straight-up reach with room for tools and materials, making them a good fit for framing, siding, MEP rough-in, and general site work on slabs or compacted soil. Platform heights in this range are 36–45 feet with working heights typically in the low-40s to low-50s. Platform capacities commonly fall between 800 and 1,500 pounds, and decks are often 5 to 7.5 feet wide with roll-out extensions for added reach. Diesel or dual-fuel power, 4WD, high ground clearance, and rough-terrain tires help with positioning on slopes and soft ground. Typical models include the Genie GS-4069 RT.

Rough-terrain scissor lifts in the 30 to 35 foot class with wide decks are built for outdoor access on unfinished surfaces where extra platform space and load capacity matter. They're a solid choice for framing, siding, steel work, and MEP rough-in when crews need room for tools and materials at height. Platform heights are 30–35 feet with working heights in the high-30s to low-40s. Wide platforms are typically 7–8 feet across with roll-out extensions that reach about 12–16 feet in length. Platform capacities commonly fall between 1,500 and 2,500 pounds. Diesel or dual-fuel power, 4WD, high ground clearance, and rough-terrain tires help with positioning on slopes and soft ground.

Telescopic boom lifts in the 40-foot class provide straight-line, out-and-up reach for outdoor work where horizontal access matters. Internal-combustion power with rough-terrain drive helps position on uneven ground, and a telescoping boom lets operators work from a safe stand-off distance. In this range, platform heights are about 40 feet. Horizontal outreach commonly falls in the low- to mid-30s feet, and platform capacity is often around 500–600 pounds for one or two workers with tools. Typical models include the JLG 400S.

Telescopic boom lifts in the 85 to 86 foot class provide long, straight-line reach for outdoor work where horizontal access is essential. They’re a strong fit for high-elevation construction access, utility work, and exterior repairs on large sites where you need to stand off and reach out to the task. In this range, platform heights are about 85–86 feet with working heights typically around 90–92 feet, horizontal outreach commonly in the low- to mid-70s feet, and platform capacities often in the 500–750 lb dual-capacity class. Internal-combustion power with rough-terrain drive and steer helps position on uneven ground, and jib plus platform rotation features support precise placement at height. Typical models include the JLG 860SJ, Haulotte HT85 RTJ O, and Genie S-85 HF.

Tracked telescopic boom lifts in the 60 to 70 foot class provide straight, out-and-up reach on soft, uneven, or sloped ground where wheeled units struggle. The track undercarriage spreads ground pressure for stability and traction in mud, sand, or snow, while the telescoping boom lets crews work from a safe stand-off distance for construction, maintenance, and industrial tasks. In this range, platform heights are about 60–70 feet with working heights typically in the high-60s to low-70s, horizontal outreach commonly in the mid-40s to mid-50s feet, and platform capacities often in the 500–750 lb class. Typical models include the JLG 660SJ Quad Track.

Telescopic boom lifts in the 60-foot class provide straight, out-and-up reach for outdoor work where horizontal access matters. Internal-combustion power with rough-terrain drive helps position on uneven ground, and the telescoping boom lets crews work from a safe stand-off distance on tasks like power line maintenance and exterior building repair. In this range, platform heights are about 60 feet with working heights typically in the mid-60s. Horizontal outreach commonly falls in the mid-40s to around 50 feet, and platform capacities are often in the 500–1,000 lb dual-capacity range. Typical models include the JLG 600S.

Telescopic boom lifts in the 120 to 125 foot class provide long, straight-line reach for tall exterior work where horizontal access is critical. They’re suited for high-rise construction, industrial maintenance, tree work, and large civil infrastructure tasks, with a straight boom that lets operators reach out and up to areas that are hard to approach with other equipment. Internal-combustion power, four-wheel drive, and steer help position on rough terrain, and continuous rotation supports efficient set-ups at height. In this range, platform heights are about 120–125 feet with working heights typically in the mid- to high-120s, horizontal outreach commonly in the 70–80 foot range, and platform capacities often between 500 and 1,000 pounds. Jib and platform rotation features allow fine positioning at the work area while maintaining stability on flat, prepared ground. Typical models include the JLG 1200SJP in this class.

Telescopic boom lifts in the 65 to 67 foot class provide straight, out-and-up reach for outdoor work where horizontal access is essential. They're a solid choice for construction access, utility work, and high-elevation painting or repair, with rough-terrain drive to position on uneven ground and a telescoping boom that lets crews work from a safe stand-off distance. In this range, platform heights are about 65–67 feet with working heights typically in the high-60s to low-70s, horizontal outreach commonly in the mid-50s feet, and platform capacities often in the 500–1,000 lb dual-capacity class. Typical models include the JLG 660SJ, Haulotte HT67 RTJ O, and Genie S-65.

Telescopic boom lifts in the 45 to 46 foot class provide straight, out-and-up reach for outdoor work where horizontal access matters. Internal-combustion power with rough-terrain drive helps position on uneven ground, and a telescoping boom lets operators work from a safe stand-off distance on tasks like utility maintenance, tree work, and exterior building repair. In this range, platform heights are about 45–46 feet with working heights in the low-50s, horizontal outreach commonly in the mid-30s to low-40s feet, and platform capacities typically between 500 and 1,000 pounds. Typical models include the JLG 460SJ, Haulotte HT46 RTJ O, and Genie S-45 HF.

Towable boom lifts in the 30 to 35 foot class provide up-and-over access with a lightweight, trailer-mounted design you can tow behind a vehicle. They're a practical choice for occasional-height tasks like tree trimming, light restoration, signage, and seasonal work where quick setup and easy transport matter. Platform heights are about 30–35 feet with working heights typically in the high-30s to around 40 feet. Horizontal outreach commonly falls in the mid-teens to about 20 feet, and platform capacities are often in the 350–500 lb range. Outriggers with auto-leveling help set up on uneven surfaces, and electric or bi-energy power supports quiet operation in residential or facility settings. Typical models include the Haulotte 3522 A and the JLG T350.

Towable boom lifts in the 50-foot class provide up-and-over reach in a lightweight, trailer-mounted package you can tow behind a vehicle. They're a practical choice for tree care, signage, light restoration, and facility maintenance where quick setup and easy transport matter. Outriggers with auto-leveling support fast, stable setup on uneven surfaces, and electric or bi-energy power keeps operation quiet in residential or campus settings. In this range, platform heights are about 50 feet with working heights typically in the mid-50s, horizontal outreach commonly in the high-20s to low-30s feet, and platform capacities often around 400–500 pounds. Typical models include the Haulotte 5533 A and the JLG T500J.

Pusharound vertical mast lifts in the 30-foot platform height class are built for single-operator indoor work where tight access and quick setup matter. They provide straight-up reach for tasks like facility maintenance, inventory pulls, signage, and light installs in warehouses and commercial interiors. Electric operation keeps noise and emissions low, and the lightweight design makes them suitable for finished floors and sensitive areas. In this range, platform heights are about 30 feet with working heights typically in the mid-30s. Platform capacities commonly fall around 300–350 lb, and overall widths are usually under 3 feet to pass through standard doorways; weights are light enough for most passenger elevators. Outriggers allow fast leveling and stable setup in confined spaces. Typical models include the Genie AWP-30S and AWP-30S DC.

Are you looking to rent a 25' vertical mast lift? Arrowhead Equipment & Supply offers a single-operator vertical mast lift rental that provides precise, low-level access for indoor and outdoor maintenance tasks. With its compact footprint and 25' working height, this mast lift is ideal for warehouses, retail spaces, and other tight-access job sites where maneuverability matters. Rent a vertical mast lift from Arrowhead Equipment & Supply for all of your overhead maintenance, installation, and inspection projects, and count on us for reliable, high-quality aerial equipment rentals.

Vertical mast lifts with a jib in the 26-foot platform height class are built for tight indoor work that needs up-and-over reach. The articulating jib helps operators clear obstacles like shelving, piping, and mezzanines while maintaining a small footprint for aisles and doorways. Electric power supports quiet, zero-emission operation on finished floors. Typical working heights land in the low-30s, with horizontal outreach from the jib commonly around the 8–12 foot range and platform capacities generally between 300 and 500 lb. Overall widths are usually about 30–40 inches, with non-marking tires and quick, simple setup for maintenance, installs, and facility work on level surfaces. Typical models include the JLG 26E and the Genie GR-26J.

Single-operator vertical mast lifts in the 20-foot platform height class are built for tight indoor access where quick setup, zero emissions, and precise positioning matter. They fit through standard doorways, maneuver easily in narrow aisles, and are a good choice for maintenance, installs, inventory pulls, and light facility work on finished floors. Working heights typically reach the mid-20s, with platform capacities commonly in the 300–500 lb range. Overall widths are usually around 30 inches to clear doors and racks, and the low machine weight helps with elevator transport and positioning on level surfaces. Typical models include the Genie GR-20, JLG MME20, and Haulotte Star 20.

Single-operator vertical mast lifts in the 12-foot platform height class are built for tight, indoor access where quick setup and zero emissions matter. They fit through standard doorways, maneuver easily in aisles, and are a good choice for maintenance, installs, inventory pulls, and light facility work on finished floors. Typical working heights reach the mid-teens, with platform capacities commonly in the 300–500 lb range. Overall widths are usually around 30 inches to clear doors and racks, and electric drive supports quiet operation with non-marking tires. Low machine weight and compact dimensions make transport and positioning straightforward on level surfaces.